IK Multimedia AXE I/O SOLO 2x3 USB Guitar Audio/MIDI Interface FREE US SHIPPING Compact audio interface with advanced guitar tone shaping Best-in-class guitar recording starts here AXE I/O, IK’s
award-winning audio interface, set a new standard for guitar-oriented recording
interfaces. Now AXE I/O Solo brings the same great tone
shaping, convenient features and premium sound to everyone, everywhere, in a
compact and affordable 2-in / 3-out format. Key Features · 2-in / 3-out USB audio interface · ACTIVE/PASSIVE pick-up selector · PURE and JFET input stages · Z-Tone® impedance-adapting circuit · Amp Out with ground loop interrupter · High-resolution, Class A mic preamp · 24-bit, 192 kHz sound quality · Wide frequency response ideal for instruments · Best-in-class analog/digital conversion · Ultra-low noise floor for high-gain recording · Designed and made in Italy Your guitar’s golden channel AXE I/O Solo offers a triple-topology instrument input
designed to preserve your guitar’s unique character, combined with powerful
tone-shaping features to adapt to any guitar or bass, and helps you coax a
wider range of sounds from any instrument. AXE
I/O Solo also offers IK’s patent pending Z-TONE® circuit,
letting you dial in impedance from 1 MOhm (“sharp”) down to 2.2 kOhms (“bold”)
that interacts with your pick-ups. At
the maximum impedance, you’ll find your sound tighter, sharper and more
precise. Increase the load and the sound becomes thicker and bolder. You’ll
quickly find yourself using these controls to give your guitars even more sonic
character – with just a few minutes’ experimentation you can dial in a sound
that fits the mix beautifully. PURE mic preamp for transparent
recording AXE I/O Solo offers a high-definition, Class A mic preamp
designed for transparent and clean recording. An extended, flat frequency
response captures the full tonal range of your voice or instrument without
coloring the sound, and best-in-class dynamic range ensures ultra-quiet
recordings. Re-amplification
made easier than ever AXE I/O Solo offers a dedicated Amp Out, a with ground-isolated
design and zero-latency routing, letting you ditch expensive and confusing
reamping setups. It’s simple: connect the Amp Out to your amp, then mic it up using
AXE I/O Solo’s microphone preamp. Now you can capture a clean copy of your
signal while recording and feed it back to your amp afterwards to experiment
with different amp, stompbox and microphone settings without re-recording
countless takes. A truly high-end audio interface for everybody The original AXE I/O set a high bar for sound quality.
AXE I/O Solo preserves the best-in-class dynamic range, ultra-low self-noise
and wide, extended frequency response essential to capturing the most accurate
details of your performance, and for keeping your sound completely pure and
transparent. Advanced digital control & routing AXE I/O Solo also includes a
powerful, convenient Control
Panel application to manage inputs & outputs and assign
routing & controller inputs. In the INTERFACE tab,
you can view the active inputs, enable phantom power and control the ground
lift to dial in the least noise for your setup. Adjust output volume, direct
monitoring routing, select the sample rate and more. The CONTROLLER tab
gives you control over the 2 controller inputs. Set behavior, MIDI channel,
MIDI CC #, minimum and maximum values, and more, to dial in the best settings
for any application you want to control. The AXE I/O Solo Control
Panel lets you keep focused on your work, instead of adjusting settings on the
unit itself, for a faster, freer workflow. Specs AXE I/O Solo Specifications Common AD and DA Resolution: 24-bit Sampling Rate: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz,
176.4 kHz and 192 kHz Host Connection: USB Type-B receptacle. USB 2.0 (High
Speed). Line Outputs 1-2 (Monitor) Configuration: Electronically balanced and floating,
automatically compensates level when connection is balanced or unbalanced,
tip hot. Output impedance: 150 Ohms balanced, 75 Ohms unbalanced Output Level: 0 dBFS corresponds to +13.5 dBu Frequency response: From 1 Hz to 46 kHz within 0.5 dB
(96 kHz sample rate) Dynamic Range: 113 dB(A) THD @ -1 dBFS: 0.001% THD+N: -103 dB(A) at -1 dBFS Channels 1-2 crosstalk: 112 dB(A) Output 3 (Amp output) Configuration: Unbalanced, floating, with selectable
ground lift Output impedance: 75 Ohms Output Level: 0 dBFS corresponds to -3 dBu Frequency response: From 20 Hz to 42 kHz within 0.5 dB
(96 kHz sample rate) Dynamic Range: 106 dB(A) THD+N: -93 dB(A) Headphones Out Output impedance: Virtually ideal source (zero Ohms)
until clipping Maximum Output level: +9 dBu into 50 Ohms load (approx
95 mW) Frequency response: From 1 Hz to 42 kHz within 0.5 dB
(96 kHz sample rate) Dynamic Range: 111 dB(A) THD+N: -102 dB(A) Instrument Input Configuration: Multiple topology instrument preamp Input impedance, PASSIVE mode: Variable from 1 MOhms
down to 2.2 kOhms Input impedance, ACTIVE mode: 10 kOhms Input level, min gain: 0 dBFS is obtained with a
+12.5dBu signal at the TS input Input level, max gain: 0 dBFS is obtained with a -19
dBu signal at the TS input Frequency response: From 6 Hz to 42 kHz within 0.5 dB
(96 kHz sample rate) Dynamic Range: 117 dB(A) THD, PURE mode: 0.002 % (-1dBFS input) THD, JFET mode: 0.5 % Mic Input Configuration: Class-A discrete differential microphone
preamp, pin 2 hot Input impedance: 4 kOhms differential Input level, min gain: 0 dBFS is obtained with a +9 dBu
signal at the XLR input Input level, max gain: 0 dBFS is obtained with a -44
dBu signal at the XLR input Frequency response: From 7 Hz to 32 kHz within 0.5 dB
(96 kHz sample rate) Dynamic Range: 116 dB(A) THD+N: -104 dB(A) at -10 dBFS Line Input Configuration: Class-A discrete differential line
receiver, tip hot Input impedance: 20 kOhms differential Input level, min gain: 0 dBFS is obtained with a +26
dBu signal at the TRS input Input level, max gain: 0 dBFS is obtained with a -27
dBu signal at the TRS input Frequency response: From 7 Hz to 32 kHz within 0.5 dB
(96 kHz sample rate) Dynamic Range: 117 dB(A) THD+N: -104 dB(A) at -10 Dbfs Connections and Controls Front Panel One 1/4" instrument input jacks Two analog potentiometers for Input GAIN Two 5 segments input level meter (peak) Analog potentiometers for Z-Tone control Pick-Up selector (PASSIVE/ACTIVE) Preamp topology selector (JFET/PURE) +48V phantom power switch USB LEDS MIDI IN/OUT LEDs Monitor knob 1/4" headphones output jack Master potentiometer for main output control 1/4" Amp output jack Rear Panel MIDI I/O 5-pin DIN connectors B-Type USB socket for connecting a computer (Mac/PC) 2 x 1/4" TRS External controllers sockets 2 x 1/4" TRS Balanced floating line outputs 1 Combo socket for MIC input and Line input (auto
selecting) Package includes AXE I/O SOLO USB A-Type to USB B-Type connection cable (1.5m/4.32ft) Dimensions Size: 19.5cm x 19.5cm x 5.3cm Weight: 1.0kg Compatibility Computers 64-bit application. Requires a 64 bit CPU and Operating System. Mac® (64-bits) Minimal: macOS
10.11 or later. One free USB port. Windows® (64-bits) Minimal: Windows
7 or later. One free USB port. Free Shipping to All USA including AK, HI, PR and other US Territories having a valid United States Postal Service Zip Code Payment & Shipping Information Paypal is our preferred method of payment. All major credit cards are accepted. Sales tax will be collected from FL state residents only. We ship using multiple carriers such as Fedex, UPS and the USPS to the 50 US states and their territories having a valid United States Postal Service Zip Code. To help ensure proper delivery of your order we prefer to send your purchase to a physical address; however, we are able to service PO Box delivery. Items are shipped within 1 business day after payment has been completed. Orders ship Monday-Friday, excluding United States federal holidays. Please note that Saturdays and Sundays DO NOT count as a business day. International Most items will ship via the Ebay Global Shipping Program. Import duties and taxes are the customer's responsibility. Buyer has to pay for any import duties and/or import taxes. You will be subject to not only customs and duty fees, but taxes such as GST in Australia and VAT in the United Kingdom. Our prices do NOT include these taxes, and they will be collected by the delivering freight company. If the shipment is refused, NO REFUND will be issued. Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying. Due to the complexity of international shipping, we are unable to accept any returns on international orders. Before making a purchase outside of the United States, please know that products sold by us use the standard 120V/60Hz voltage standard. We are not responsible for any damage caused by not adhering to the voltage requirements.
Returns Accepted for this item if it's within 30 Days